Virat Special Steels
tuv

Alloy and Tool Steel for the Railway Industry in India

Railway components such as axles, pins, gear holders and crank parts carry heavy, repeated loads for years, so the steel grade, its heat treatment and the test documents behind it matter as much as the price.

  • Since 1957 Supplying the forging industry
  • 35+ Grades
  • 1800+ Customers
  • 3,500+ tons Stock capacity across our yards

Contact Virat Special Steels

Virat Special Steels supplies alloy steel and tool steel to railway component manufacturers, forging shops and machine shops. We supply the steel, to the grade and specification you name, not finished railway parts. We hold stock in Ludhiana and Gurugram, with band saw cutting up to 2500 × 1100 mm, a machining shop, and in-house spectro, UT and hardness testing.


Which Steel for Which Railway Job

Typical need Grades we stock Notes
Axles, pins, shafts and crank parts machined from bar 40NiCrMo84 (EN24) Through-hardening alloy steel, normally heat treated by the buyer. Condition and hardness
Gears, gear holders and case-hardened parts 20NiCrMo5 (EN353), 16MnCr5, 20MnCr5 Case-hardening alloy steels: hard surface, tougher core.
Bogie and compressor components 40NiCrMo84 or 20NiCrMo5, as your drawing specifies The drawing and specification decide the grade.
Dies for forging railway components DB6 / DIN 1.2714, H13 / DIN 1.2344, H11 / DIN 1.2343 Hot work tool steels. See our forging die steel page.
A grade or standard not listed here Ask us Send the specification and we will tell you what we can supply.
These are starting points. Railway parts are usually made to an approved drawing and specification, and that decides the grade.

Specifications and Documents

Railway parts are often built to Indian Railways (RDSO), OEM or customer-specific specifications. Send us the specification, the heat-treatment condition and the reports you need when you enquire. We confirm what we can supply and which documents are available for your grade and lot. We do not claim approval or compliance before we have seen the requirement.

If your part needs a specific mill or an approved source, say so in your RFQ so we can tell you at once whether we can meet it. Safety-critical parts should always follow your approved specification.


Services around the steel

  • Ready stock Material is held in Ludhiana and Gurugram for off-the-shelf supply
  • Cut to size Band saw cutting to your block or bar length, so you pay for steel you will use.
  • Machining Squaring and other value-adding work in our machining shop
  • Testing Chemical analysis, UT and hardness checks in-house
  • Technical advice Help with grade choice and heat treatment questions.

How to order

  • Send us the grade, size, quantity and delivery location
  • Tell us the delivery condition and the test certificates you need
  • We reply with stock status, delivery time and a quotation
  • We cut, machine and dispatch to your plant

About Virat Special Steels

We began in 1957 as Dhingra Enterprises, supplying tool and die steel to India’s forging and casting industry. Today we stock tool, die and alloy steels, import from mills in Europe, Japan, South Korea and Brazil, and handle cutting, machining and testing at our own facility.

Questions Railway Buyers Ask

It depends on the approved drawing and specification. Heavily loaded pins, shafts and crank parts are often machined from through-hardening alloy steel such as 40NiCrMo84 (EN24), while gears and similar parts may use a case-hardening steel such as 20NiCrMo5 (EN353). Always follow your approved specification.
EN24 (40NiCrMo84) is a through-hardening alloy steel, hardened right through the section. EN353 (20NiCrMo5) is a low-carbon case-hardening steel, which gets a hard surface and a tougher core after carburising. Limits differ between standards, so confirm on the mill certificate.
Tell us the specification at the enquiry stage. We confirm what we can supply and which documents are available for your grade and lot. We do not claim approval or compliance before we have seen the requirement.
Yes. Forging shops making railway components use hot work tool steels for their dies. We stock DB6 (DIN 1.2714), H13 (DIN 1.2344) and H11 (DIN 1.2343) for this.
Yes. Our band saws cut up to 2500 × 1100 mm, and our machining shop can square and finish blocks. Send us the size you need and we will confirm what is in stock and what can be cut.
We have an in-house chemical and spectro lab, a UT testing machine and a hardness tester. Tell us at the enquiry stage which reports and certificates you need, and we will confirm what can be issued for your grade and lot.
Call +91 98140 21775, email info@viratsteels.com, message us on WhatsApp or use the enquiry form. Give us the grade, size, quantity, delivery location, delivery condition, specification and the testing documents you need. We reply with stock status and a quotation.

Stocking Partners

We Keep The Materials From India, Japan, South Korea, Italy, Germany, France, Brazil.

india     japan     south-korea     italy     germany     france     brazil
Inquire Now Product

Products

 

  • Corporate Office: C-545, Sector-37, Pace City - II, Gurgaon 122001 (Haryana) India
  • UNIT-I: C-146, Focal Point, Phase - V, Ludhiana 141010 (Punjab) India
  • UNIT-II: NH-1, G.T. Road, Opp. Sarita Forging, Rajgarh, LDH (Punjab) India

 

payment